Data: 2010-02-11 00:08:55 | |
Autor: Tomasz Chmielewski | |
Jak wykazać, że urządzenie nie posiada interfejsu USB 2.0 | |
On 10.02.2010 20:52, Czeresniak wrote:
Czy istnieją jakieś oficjalne aplikacje mogące wykazać czy podłączone do Odpal jakiegos Linuksa livecd. Zaloguj sie jako root, podlacz urzadzenie, wpisz "dmesg -c". Jak urzadzenie jest USB 2.0, powinienes gdzies zobaczyc: new high speed USB device using ehci_hcd and address ... Jak urzadzenie jest USB 1.1, powinienes zobaczyc: new full speed USB device using uhci_hcd and address ... -- Tomasz Chmielewski http://wpkg.org |
|
Data: 2010-02-11 21:31:51 | |
Autor: Czeresniak | |
Jak wykazać, że urządzenie nie posiada interfejsu USB 2.0 | |
Tomasz Chmielewski pisze:
Odpal jakiegos Linuksa livecd.tak też zrobiłem i wynik po podłączeniu telefonu jest taki (tryb Transfer danych): [ 589.300000] usb 4-1: new full speed USB device using uhci_hcd and address 2 [ 589.524000] usb 4-1: configuration #1 chosen from 1 choice [ 589.532000] scsi6 : SCSI emulation for USB Mass Storage devices [ 589.532000] usb-storage: device found at 2 [ 589.532000] usb-storage: waiting for device to settle before scanning [ 594.532000] usb-storage: device scan complete [ 594.536000] scsi 6:0:0:0: Direct-Access Nokia E51 1.0 PQ: 0 ANSI: 0 [ 594.544000] sd 6:0:0:0: [sdb] 7951360 512-byte hardware sectors (4071 MB) [ 594.548000] sd 6:0:0:0: [sdb] Write Protect is off [ 594.548000] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 594.548000] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 594.556000] sd 6:0:0:0: [sdb] 7951360 512-byte hardware sectors (4071 MB) [ 594.560000] sd 6:0:0:0: [sdb] Write Protect is off [ 594.560000] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 594.560000] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 594.560000] sdb: [ 594.860000] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 594.860000] sd 6:0:0:0: Attached scsi generic sg2 type 0 lub taki (tryb PC Suite): [ 834.944000] usb 4-1: new full speed USB device using uhci_hcd and address 3 [ 835.112000] usb 4-1: configuration #1 chosen from 1 choice [ 835.120000] scsi9 : SCSI emulation for USB Mass Storage devices [ 835.120000] usb-storage: device found at 3 [ 835.120000] usb-storage: waiting for device to settle before scanning [ 838.472000] usb 4-1: USB disconnect, address 3 [ 839.216000] usb 4-1: new full speed USB device using uhci_hcd and address 4 [ 839.388000] usb 4-1: configuration #1 chosen from 1 choice [ 841.996000] cdc_acm 4-1:1.10: ttyACM0: USB ACM device [ 842.000000] usbcore: registered new interface driver cdc_acm [ 842.000000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters [ 842.148000] usbcore: registered new interface driver cdc_ether [ 842.152000] usb 4-1: bad CDC descriptors [ 842.152000] usbcore: registered new interface driver rndis_host a po podpięciu pamięci flash USB: [ 688.372000] usb 2-2: new high speed USB device using ehci_hcd and address 4 [ 688.504000] usb 2-2: configuration #1 chosen from 1 choice [ 688.508000] scsi7 : SCSI emulation for USB Mass Storage devices [ 688.508000] usb-storage: device found at 4 [ 688.508000] usb-storage: waiting for device to settle before scanning [ 693.508000] usb-storage: device scan complete [ 693.508000] scsi 7:0:0:0: Direct-Access USB Flash Memory 1.00 PQ: 0 ANSI: 2 [ 693.508000] sd 7:0:0:0: [sdc] 7827392 512-byte hardware sectors (4008 MB) [ 693.508000] sd 7:0:0:0: [sdc] Write Protect is off [ 693.508000] sd 7:0:0:0: [sdc] Mode Sense: 65 44 09 30 [ 693.508000] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 693.512000] sd 7:0:0:0: [sdc] 7827392 512-byte hardware sectors (4008 MB) [ 693.512000] sd 7:0:0:0: [sdc] Write Protect is off [ 693.512000] sd 7:0:0:0: [sdc] Mode Sense: 65 44 09 30 [ 693.512000] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 693.512000] sdc: sdc1 [ 693.516000] sd 7:0:0:0: [sdc] Attached SCSI removable disk [ 693.516000] sd 7:0:0:0: Attached scsi generic sg3 type 0 Jak widać interfejs telefonu jest Full Sped USB a więc USB 1.1. W jaki sposób można to jeszcze potwierdzić najlepiej pod systemem produkcji MS? Pozdrawiam Darek |
|
Data: 2010-02-14 17:46:37 | |
Autor: Radosław Sokół | |
Jak wykazać, że urządzenie nie posiada interfejsu USB 2.0 | |
W dniu 2010-02-11 21:31, Czeresniak pisze:
Jak widać interfejs telefonu jest Full Sped USB a więc USB 1.1. Full-speed to również jeden z trybów pracy USB 2.0, więc to wcale o niczym nie przesądza. -- |""""""""""""""""""""""""""""""""""""""""""""""""""""""""""| | Radosław Sokół | http://www.grush.one.pl/ | | | Politechnika Śląska | \................... Microsoft MVP ......................../ |
|
Data: 2010-02-14 21:24:36 | |
Autor: Tomasz Chmielewski | |
Jak wykazać, że urządzenie nie posiada interfejsu USB 2.0 | |
On 14.02.2010 17:46, Radosław Sokół wrote:
W dniu 2010-02-11 21:31, Czeresniak pisze: Wtedy byloby chyba: New full speed USB device using ehci_hcd (ehci_hcd to sterownik do USB 2.0). -- Tomasz Chmielewski http://wpkg.org |
|